10
EN
RUCKUS
SHOCK CLEANING
Oil-lledshockswillrequireregularmaintenanceduetotheoil
breaking down or getting dirty. This maintenance should be performed
after about every 3 to 5 hours of use, depending on the conditions that
the vehicle is used in.
•Removetheshockfromthevehicle.
•Removethecapfromtheshockbodyanddisposeoffluid.
•Disassembletheshock.CleanthoroughlywithDYN5505.
Dry parts before assembly.
•Re-assembletheshockandrefilltheshockbodywithsilicone
fluid (30 weight recommended).
•Slowlymovetheshaftandpistonupanddowntoremove
air bubbles.
•Movethepistontothemidwaypointofthebodyand
install the cap.
•Wipeoffanyoverflowingfluid.
•Whenproperlyfilled,thepistonshouldreboundabout
3/8 in (9.5mm) after being pushed in fully.
•Re-installtheshockonthevehicle.
Ride Height Adjustment
Ride height is an adjustment that affects the way the vehicle
jumps, turns and goes over bumps. Drop one end of the vehicle from
approximately6inches(152mm)inheightontoaatsurface.When
dropping the front of the vehicle, after the vehicle settles, make
sure the front arms are equal and parallel to the flat surface. Do
the same with the rear to make sure both arms are parallel with
the flat surface.
Lowering the front ride height increases steering, but decreases
traction. Lowering the rear ride height increases traction, but
decreases steering.
Part # Description
ECX1036 Shock Body Set
ECX1037 Shock Caps, Pistons
ECX1038 Shock Parts Set
ECX1039 Front Shock Shaft (2)
ECX1040 Rear Shock Shaft (2)
ECX1041 Front Shock Springs (2)
ECX1042 Rear Shock Springs (2)
ECX1043 ShockO-RingSet
No. Description
TAPPING BINDER HEAD M3x10mm
TAPPING BINDER HEAD M3x12mm
TAPPING FLAT HEAD M3x15mm
TAPPING FLAT HEAD M3x12mm
TAPPING FLAT HEAD M3x10mm
TAPPING BINDER HEAD M3x18mm
TAPPING FLAT HEAD M2x16mm
TAPPING BINDER HEAD M3x16mm
No. Description
WASHER 5x7x0.5mm
E-CLIP E2.5
LOCK WASHER
FLANGED LOCK NUT M4
WASHER 3x8x0.5mm
LOCK NUT M3
WASHER 2x7x0.5mm
SET SHAFT SCREW M3x13mm
No. Description
BUTTON HEX M2.5x4mm
SETSCREW M3x3mm
SETSCREW M3x12mm
STEP SCREW M3x0.5x13.4mm
STEP SCREW M3x0.5x10.5mm
BUTTON HEX M2.5x8mm
STEP SCREW M3x0.5x7.4mm
No. Description
BINDER HEAD M3x8mm
BINDER HEAD M3x12mm
BINDER HEAD M3x20mm
BINDER HEAD M3x25mm
BUTTON HEAD M3x30mm
BUTTON HEAD M2x6mm
TAPPING BUTTON HEAD M3x10mm
REAR SHOCK FRONT SHOCK
ECX1043
ECX1037
ECX1037
ECX1041
ECX1037
ECX1043
ECX1036
ECX1038
ECX1038
ECX1043
ECX1037
ECX1037
ECX1038
ECX1042
ECX1040
ECX1057
ECX1037
ECX1043
ECX1038
ECX1039
ECX1036
ECX1038
ECX1038
ECX1037
ECX1057
FASTENERS
Comments to this Manuals