ECX Torment Instruction Manual download pdf (Page 10)

torment

™

Description

Tapping Binder Head, M3x8mm

Tapping Binder Head, M2.5x4mm

Tapping Binder Head,

M3x10mm

Tapping Binder Head,

M3x14mm

Tapping Binder Head,

M3x16mm

Tapping Binder Head,

M3x18mm

Tapping Binder Head,

M3x20mm

Tapping Binder Head,

M3x22mm

Tapping Binder Head,

M3x25mm

Binder Head, M3x10mm

Tapping Flat Head, M2.5x10mm

Tapping Flat Head, M3x10mm

Tapping Flat Head, M3x15mm

Tapping Binder Head,

M3x12mm

Washer,

6.2x10.8x0.2mm

Flanged Lock Nut, M4

Washer,

3x8x1mm

Lock Nut M3

Washer,

2.6x6 X0.5mm

Lock Nut M2.5

Setscrew, M3x3mm

Setscrew, M4x3mm

Binder Head, M3x20mm

Binder Head, M3x22mm

Flat Head, M3x8mm

Flat Head, M3x10mm

Flat Head, M4x18mm

Binder Head, M3x12mm

Binder Head, M3x14mm

Binder Head, M3x16mm

Binder Head, M3x18mm

Description Description Description

FASTENERS

SHOCK CLEANING

Oil-lledshockswillrequireregularmaintenanceduetotheoilbreaking

down or getting dirty. This maintenance should be performed after about

every3to5hoursofuse,dependingontheconditionsthatthevehicleis

used in.

•Removetheshockfromthevehicle.

•Removethecapfromtheshockbodyanddisposeoffluid.

•Disassembletheshock.CleanthoroughlywithDYN5505.Dryparts

before assembly.

•Re-assembletheshockandrefilltheshockbodywithsiliconefluid(30

weight recommended).

•Slowlymovetheshaftandpistonupanddowntoremoveairbubbles.

•Movethepistontothemidwaypointofthebodyandinstallthecap.

•Wipeoffanyoverflowingfluid.

•Whenproperlyfilled,thepistonshouldreboundabout3/8in(9.5mm)

after being pushed in fully.

• Re-installtheshockonthevehicle.

Ride Height Adjustment

Ride height is an adjustment that affects the way the vehicle jumps,

turnsandgoesoverbumps.Droponeendofthevehiclefromapproxi-

mately 6 inches (152 mm) in height onto a ﬂat surface. When dropping

the front of the vehicle, after the vehicle settles, make sure the front

arms are equal and parallel to the ﬂat surface. Do the same with the rear

to make sure both arms are parallel with the ﬂat surface.

Lowering the front ride height increases steering, but decreases

traction. Lowering the rear ride height increases traction, but decreases

steering.

Part # Description

ECX233000 Shock, Complete, (2): 4wd

ECX233001 Shock Rebuild, (2): 4wd

ECX233002 Top, Bottom Shock Ends: 4wd

ECX233003 Shock Spring, Black, Set: 4wd

Part # Description

ECX234005 Link Set, Plastic: 1:10 4wd All

ECX236001 Lock Nut, M2.5, (5)

ECX236004 Special Hardware: 1:10 4wd All

ECX233000

ECX233001

ECX233002

ECX234005

ECX236001

ECX236004

ECX233001

ECX233002

ECX234005

ECX233003

SHOCK PARTS

DIAGRAM

1 2 ... 5 6 7 8 9 10 11 12 13 14

Comments to this Manuals

No comments

ECX Torment Instruction Manual Page 10

Comments to this Manuals

Related products and manuals for Remote controlled toys ECX Torment